AEG Appliance Repair in Bewbush & North Broadfield

What does error code EH0 mean on an AEG washing machine?

Error code EH0 (and EH1, EH2, EH3) on an AEG washing machine indicates a power supply issue - the voltage may be too low, too high, or unstable. Unplug the appliance. Test the socket with another appliance and check your home's electrical supply is stable. Do not use extension cables. If the problem persists, contact a qualified electrician to inspect your electrical installation.

What does error code E20, E21 or C2 mean on an AEG washing machine?

Error codes E20, E21 or C2 on an AEG washing machine indicate a drainage problem - the machine cannot drain water properly. Switch off the appliance and unplug it from the mains before any inspection. Clean the pump filter, check the drain hose is not kinked or blocked, and ensure it is positioned correctly (no more than 10cm into the drain, between 60-100cm above floor level). If the problem persists, contact a qualified technician.

What does error code i30 mean on an AEG dishwasher?

Error code i30 on an AEG dishwasher indicates water has been detected in the base of the appliance. Do not stand in any pooled water near the appliance. If safe to do so, switch off at the mains and turn off the water supply - only unplug if you can do so without risk of water contact. Leave overnight to allow any foam to disperse. Check for visible leaks around the door seal. If the problem persists, contact a qualified technician.

What does error code E4 mean on an AEG hob?

Error codes E4 or E4xx on an AEG hob indicate the overheating protection has activated. Switch off the hob immediately. Do not touch the cooking surface - allow it to cool completely until the residual heat indicator is off before handling any cookware. Ensure your cookware is induction-compatible with a flat base. If the error persists after cooling, contact a qualified technician.

What does error code i10, i11, AL5 or C1 mean on an AEG dishwasher?

Error codes i10, i11, AL5 or C1 on an AEG dishwasher indicate a water inlet problem - the dishwasher is not receiving water. Switch off the appliance before any inspection. Check the water tap is fully open, inspect the inlet hose for kinks, and clean the filter. If the problem persists, contact a qualified technician.

What temperature should I set my AEG wine cooler to?

For cellaring wines long-term, maintain a temperature between 12-14°C. For serving, white wines and sparkling wines are best at 6-12°C, while red wines are optimal at 14-20°C.

How do I use the AEG ProSteam function on my washer dryer?

The ProSteam function uses steam to reduce creases and refresh garments. Select ProSteam as a standalone cycle for lightly worn clothes that need freshening, or add it to a wash programme to reduce ironing time. ProSteam is gentle on fabrics and helps reduce allergens.

Where can I find the model and serial number on my AEG appliance?

The rating plate with model (PNC) and serial number is typically located: on washing machines and dryers, inside the door frame; on dishwashers, inside the door edge; on fridges and freezers, inside on the left wall; on ovens, behind the door on the frame; on hobs, on the underside. You will need these numbers when ordering spare parts or booking repairs.

How do I clean mould from the door seal on my AEG washing machine?

Switch off and unplug the machine before cleaning. Clean rubber door seals using sodium carbonate crystals, thick bleach, or dishwasher cleaner to dissolve stubborn mould and soap residue. Never mix different cleaning products as this can create toxic fumes. Ensure good ventilation during cleaning. Wear rubber gloves and protective goggles.

How often do I need to refill the rinse aid in my AEG dishwasher?

A full tank of rinse aid lasts for approximately 10 to 20 washes, depending on the water hardness setting. The dishwasher will indicate when the rinse aid reservoir needs topping up, usually when the indicator becomes transparent.